Reaching the final stage of building a brand-new home on the Gold Coast is an exhilarating milestone. Your builder sends the exciting notice of Practical Completion (PCI), accompanied by the final 5% progress claim invoice and an invitation to conduct the final walk-through.
However, this is also the moment of maximum legal and financial vulnerability for the homeowner. Under Queensland domestic building contracts, once you pay that final progress claim and collect the keys, your financial leverage over the builder drops to zero. Getting a builder back to fix defects after final payment can take months of frustrating disputes.
What Exactly Is Practical Completion (PCI)?
According to the Queensland Building and Construction Commission (QBCC), Practical Completion is defined as the stage where the building works are completely finished in accordance with the contract plans and specifications, reasonably fit for occupation, and free from all major defects.
Many volume project builders rush the PCI walk-through, giving buyers just 30 to 45 minutes to inspect a 300m² two-storey home. An untrained eye will notice a scratch on a kitchen door, but will completely miss missing roof truss bracing, inadequate shower fall, uninsulated ceiling zones, or unsealed brick articulation joints.
Critical Legal Advice
Do not hand over the final payment until you have conducted an independent Handover (PCI) Inspection. You have the legal right under QBCC legislation to submit an official builder defect rectification list.
The 5 Essential Areas of an Independent PCI Audit
1. The Roof Void & Structural Framing
This is the area project managers pray you never look into. A licensed builder climbs into the manhole to examine:
- Truss Bracing & Gang Nails: Ensuring metal tie-down brackets and speed braces match engineering specifications.
- Ceiling Insulation Continuity: Checking for gaps around downlights and ducting that cause thermal bridging and skyrocketing air conditioning costs.
- Sarking & Valley Flashings: Confirming reflective roof sarking is continuous with zero rips or missing flashings.
2. Wet Area Waterproofing & Tile Falls
Water must drain freely to the waste grate in all shower enclosures and bathroom floors. We test falls with digital levels to identify "ponding" where stagnant water will sit, decay grout, and cause chronic mold. We also verify mandatory Form 16 / Form 43 waterproofing compliance certificates.
3. Plaster Finish, Paint Quality & Cornices
Inspecting interior walls under glancing light in accordance with the QBCC Standards and Tolerances Guide. We identify joint flashing, visible screw pops, unlevel architraves, and substandard paint coverage where primer or plaster shows through.
4. Doors, Windows & Architectural Hardware
Checking that every sliding stacker door, awning window, and internal passage door latches smoothly without binding. Inspecting external perimeter mastic sealing to prevent coastal wind-driven rain penetration.
5. Brickwork, Articulation Joints & Termite Barrier
Verifying that vertical brick expansion joints are filled with flexible backing rod and sealant (not hard mortar). Ensuring that perimeter weep holes remain unobstructed by external concrete paths and that the AS 3660.1 termite barrier notice is permanently fixed in the electrical meter box.
Essential Handover Inspection Checklist
| Item Inspected | QBCC Compliance Standard | Common New Build Failure |
|---|---|---|
| Shower Waste Fall | Minimum 1:60 to 1:80 gradient to drain | Flat tiles causing water ponding outside the screen |
| Internal Paintwork | Uniform opacity viewed from 1.5m in non-glancing light | Thin roller stippling and missed second coats |
| Roof Void Insulation | Continuous R-value rating with zero gaps | Insulation batts kicked aside by ducted AC trades |
| Weep Hole Clearance | 75mm clearance to finished ground / 50mm to paving | Concreters pouring footpaths over weep holes |
| External Flashings | Continuous lap joints over window and door heads | Missing or unsealed end-caps causing wall leaks |
How An Independent Builder Report Protects Your Warranty
Queensland builders are bound by a 6-year 6-month statutory warranty for structural defects and 12 months for non-structural minor defects. However, getting items repaired post-handover requires lodging formal disputes with the QBCC.
When registered builder Garry Witt conducts your PCI audit, you receive a clear, legally backed photo defect document referencing exact Australian Standard clauses. Builders respond with urgency because the report is authored by an experienced peer who speaks their technical language.
Approaching Handover On Your New Gold Coast Home?
Book your Practical Completion Inspection (PCI) with registered builder Garry Witt today. Receive an exhaustive defect report the same evening to submit directly to your site supervisor.